8,000,000 BTU/hr fired heating units
The FourQuest Energy fired heating units are coupled with a shell and tube heat exchanger using glycol as a heating medium. Our fired heating units are specifically designed to safely heat most liquids—even corrosive and severe chemicals—without worry. They have a thermal output of 8,000,000 BTU/hr and a maximum flow rate capacity of 500 L/min at 150 psig discharge pressure.
The units are able to adapt to every heating need in the energy industry, from contaminated ice melting in pipelines due to cold weather to heating boiler feed water for plant startup. Our fired heater can increase the temperature of water up to 50°C in a single pass and has a maximum outlet temperature of 120°C. The fired heating units have excellent thermal efficiency, are very safe, and consume only diesel fuel.
38,000,000 BTU Frac Water Heater
Our 38,000,000 BTU frac water heaters are dual fired – diesel or natural gas – trailer mounted, fully enclosed units. These units are capable of heating water up to 100°F in a single pass at a flow rate of 500GPM, with a maximum flow rate of 850GPM at 50 psi (inlet pressure). The dual burners included on each unit meet all NFPA combustion system requirements and are equipped with safety shutdowns. Burners are digitally controlled to ensure adequate water temperatures are being achieved.
Chemical cleaning often requires fluid temperatures up to 80°C for optimal degreasing and decontamination. The 8 MBTU/hr fired heating units are ideal for heating larger system volumes for chemical cleaning; required temperatures can be reached very quickly. Higher temperatures in chemical cleaning solutions mean faster reaction times and improved cleaning.
FourQuest Energy has a wide range of experience and capability in commissioning services. It is essential in the energy industry to ensure required temperatures are met for plant startup; our company can warm water for plant start up and maintain temperature for operations using our fired heating units. Circulation loops can be established between process water tanks and our heaters to maintain fluid temperature.
Практическая оценка объема работ по очистке трубопроводных систем важна на всех этапах строительства, запуска и эксплуатации объектов. С точки зрения подрядчика по очистке, эффективная оценка объема работ по очистке трубопроводных систем является ключевым элементом для составления эффективных пакетов услуг по очистке. Оценка объема работ по очистке систем с учетом объема продукции способствует выполнению очистки при вводе в эксплуатацию на месте. Например, когда системы рассчитаны на несколько видов продукции или имеют короткие участки трубопроводов, сложно создать эффективные пакеты очистки. Эта проблема усугубляется, когда системы не передаются для очистки в ожидаемом порядке. Очистка большой системы может быть задержана, если часть трубопровода принадлежит другой системе. FourQuest может помочь клиенту в разработке объемов работ по системам, что не только будет способствовать окончательной сдаче строительства, но и сэкономит значительное время при разработке и выполнении процедур. Помимо возможности оценки трубопроводных систем для определения объема работ, FourQuest может предоставить экспертизу по определению объема работ по электрооборудованию и контрольно-измерительным приборам, что приведет к созданию полного пакета определения объема работ по системе.
Fluid temperature is affected by various outside factors, such as weather conditions, ambient temperature, and pipe location. Certain temperatures need to be maintained when performing tests such as hydrostatic pressure testing; fired heating units can be used to achieve these temperatures. If piping or a tank has a minimum metal temperature to be met during testing, the use of a fluid heater will allow the test to proceed during marginal temperature conditions.
Hydraulic fracturing uses certain hydrocarbons or water for injection that require various temperatures for maximum effectiveness. One of the major challenges of hydraulic fracturing includes heating fluids in cold weather conditions in order to prevent freezing of water. Our fired heating units can easily maintain heat for fracturing fluids for extended periods of time on down-hole sites.
